Your position: Home / Controller Kit

MKS GEN L+TFT32+WIFI

K04
Price:
USD
$45.00
    Please select the information you wantX
  • size:
    GEN-L+TFT32+WIFI
    GEN-L+TFT32
Quantity:
-
+
(2000 available)
  • Description
  • Size Chart
  • Measurement
  • Color Chart
  • Reviews

  Name: MKS GEN-L V1.0
  This controller board is integrated which is based  on  Marlin open source,
  greatly compatible with   Ramps1.4. Further, it is good cost effective with high performance.
 
 
  Shipping List

Kit1
 1* MKS Gen-L V1.0     
 1*MKS TFT32 V4.0
 1*MKS WIFI Module
 1*USB
 1*Flat cable
 3*Endstop
 1* Screwdriver

Kit2
 1* MKS Gen-L V1.0     
 1*MKS TFT32 V4.0
 1*USB
 1*Flat cable
 3*Endstop
 1* Screwdriver
 
 
  Features
Assembly with high quality MOSFET which is good at cooling and ensure stable working in a long time.
Use dedicated  power chip which has excellent cooling and stable electricity.
Adopt stable and reliable  filter circuit  to reduce  interference. Improve printing performance.
Highly, improve the MOSFET cooling of heated bed .
It is easy and safe to assemble motors, drivers and endstops in different color.
More features as following

 gen-l

 

 

 

Wiring

 

GEN-L wiring

 

 

 

 

  PINOUT

 

GEN-L PIN

 

 

 

 SIZE

GEN-L SIZE

 

 

 

The direction of stepper drivers on board.

 

GEN-L

 

 

 

How to Adjust Driver Current.
 
Caution!
Please mind the power polarity and  drivers direction.
Please don’t put the drivers or motors on/off while power on.
Please disconnect all motors when adjust driver current.

 
 
A4988(1amp)
I= vref /1.6,default Vref 1.6V and 0.5A,Max1.0A.
 
A4988(2amp)
I= vref /0.8,default Vref 0.8V and 1.0A,Max2.0A.
 
DRV8825
I= vref *2, default 0.65A and 1.3A,Max 2.5A.
 
LV8729
I= vref /0.5, default 0.4A and 0.8A,Max 1.5A.

microstep
 
 
 
Following picture shows how to check the Vref.

 

 

 

rated current

 

 

 

 

 

Name:MKS TFT32 Touch Screen
 
MKS TFT32 is a colorful touch screen which is used independently on 3d printer.
This display is no need to set mainboard firmware and work together directly.
And it is easy to replace into your logo and edit your local language.
Also, it is available to self-define some commands .
Attention: MKS TFT32 can’t work with Ramps1.4.
More features as follows:

TFT321
TFT322

 

Wiring

 

IMG_20180507_222152

 

 

 

 

Size

 

TFT32 SIZE

 

 

 

How to assemble with mainboard.
Set the baud rate, ensure both  TFT and controller board are the same.
 
1.MKS Series mainboards
Such as, MKS SBASE,MKS MINI,MKS GEN,MKS BASE, MKS GEN L,etc.
Flash firmware to mainboard .( TFT display has updated latest config inside already).
Connect TFT display to AUX-1 of the board.
No need to configure on board firmware,they will work together directly after wire.
The boards need a external 12V power supply.
 
2.Firmware Update
Please copy following documents to the root of SD card.
(Please don’t edit the documents name.)
mks_pic        mks_config        mkstft28
Then, plug the SD card to the TFT and power on. It  will update automatically.
 
 
3.Config

config-1

config-2

 

4.Bed Leveling
 
Auto Leveling
After the machine assembles with a bed leveling controller, then run leveling on TFT interface.
#The command of auto leveling (G29 is available for Marlin.
While G32 is for  Repetier and Smoothieware)
>cfg_auto_leveling_cmd:G28;G29;
 
Manual Leveling
Manual leveling is good for MB,i3 etc machines. It is available to set 3,4,5 point .
#The point number of manual leveling:(3,4,5 point available)
>cfg_point_number:4
 
 
5.Filament Replace
It is easy to replace the filament when it runs out.
You are able to set temperature and the speed of filament in-out on config.
As following:
#the speed of filament replacing(mm/min)
>cfg_filament_change_speed:1200
 
#the length of filament replacing(mm)
>cfg_filament_change_step:5
 
#the min temperature of filament replacing
>cfg_filament_limit_temperature:175
Then, here is the steps to replace filament.
1).On printing
pause-----more-----change----in/out-----stop
 
2).Before start printing
set-----change-----preheat-----in/out-----stop

 
6.Print from Breakpoint
TFT has a one of the excellent features is able to print from Breakpoint.
Below is the way to do it.
Firstly, set target temperature of extruder and heated bed, and then preheat.
Secondly, when preheat ready, go home .(Notice: if power off happens during operating printing from breakpoint, please must home .)
Thirdly, move extruder to the breakpoint which is available to set allowable error.
#Breakpoints continued playing Z-axis error setting
>cfg_breakpoint_z_error:0.2
Fourth, click set, and then click Continue(Means Print from Breakpoint).
After that, choose the file you want.
(If  you pause the printing, and turn the printer off,
then it will resume to print from the pause point after power on.)
 
  
7.Filament Outage Detecting
Connect detecting switch to PB1 of TFT.
Set configuration to trigger low level or high level available.
 #the level signal of outage detection module PB1(low level:0; high level:1)
>cfg_PB0_PB1_Level:1
 
 
8. Auto off after Print Finishes
Enable this function on config,and  take concerted with PWC switch.
#whether set machine auto-off after print finishes(auto-off:1; NO:0)
>cfg_print_finish_close_Machine:0

1
 
9. MKS WIFI
MKS TFT supports WIFI remote control. Please set configurations.
As follow:
#wifi mode(AP:1; STA:2)
>cfg_wifi_mode:1
 
#wifi name and password
>cfg_wifi_ap_name:MKS_wifi
>cfg_wifi_key_code:makerbase
 
#Dynamic access IP
>cfg_ip_dhcp_flag:1
 
#IP/mask/gateway
>cfg_ip_address:192.168.3.100
>cfg_ip_mask:255.255.255.0
>cfg_ip_gate:192.168.3.1


10.WiFi Wiring on TFT
IMG_20180507_222021_


 

Please be aware that due to your computer monitor display the color may have some difference between the picture and the physical item

Please according to you to buy the dress fabric, select the corresponding fabric color chart

Average rating:
Share your thoughts with other customers
Write a review
Product reviews can be carried out after the member login, please click here to login